*************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************

出口法國法國禮品商務禮品定時開關定時插座

1． 將常通開關撥到下面，露出“圓圈”位置，此時定時功能開。

2． 校對當前時刻。順時針旋轉刻度盤，讓箭頭指向當前時刻。

3． 撥動插片設置程序。每個插片為15分鐘，按到下面時該段時間設置為接通。

4． 把本定時器插入電源，表示定時器進入工作狀態，再把用電器插頭插入定時器插座，打開用電器開關即可。

Turn the switch to“”to enable the timing function.

1. Adjust current time,and then turn the dial clockwise to make the arrowhead point at the position of current time.
2. Set up timing program by pulling patches.Each of the patches indicates 15 minutes power on or off. The timer powers on when the patch stays outmost side.
3. Plug in then the timer is working.Plug the electrical appliance into the timer and power it on.

譬如：現在是早上8:00，您想讓用電器在10:15~11:00工作，您就旋轉刻度盤，讓箭頭指向8:00，再把10:15到11：00的三個插片按到下面（如圖示），用電器就能在那段時間內自動工作了。如果需要，您可以每天進行多48段編程，讓用電器在一天的不同時段自動運行。

如暫時不需要定時功能，可把常通開關撥到上面，露出“I”標志，此時定時功能關，電路處于常通狀態。

The current time is 8:00 am,and you want the electrical appliance to work from 10:15 am to 11:00 am.First,turn the dial clockwise to make the arrowhead point at 9:00 am.Then pull out the three patches between 10:15 am to 11:00 am to outmost position(see the picture).The plugged in electrical appliances can work from 10:15 am to 11:00 am automatically.You can program the automatically.

Turn the switch back to“I”to disable the timing function and power on the timer.

注意事項：Warning

※本品所接電器功率總和不得超過額定功率；

※本品斷電后必須重新校隊當前時刻；

※除非改變?cè)O(shè)置，否則每天保持一致的程序；

※請勿擅自拆卸定時器后蓋。

※The total power of the electrical appliances connected the the timer can not exceed the timer’s rated power capability.

※Readjust current time if power of the timer turns off.

※The timing program keeps unchanged unless setup changes.

※Do not dismantle the back cover from the timer.